Logo
Builders' Plan Gallery  |  Hip Pocket Web Site  |  Contact Forum Admin  |  Contact Global Moderator
September 22, 2018, 12:43:11 PM *
Welcome, Guest. Please login or register.
Did you miss your activation email?

Login with email, password and session length
 
Home Help Search Login Register
Pages: 1 [2]   Go Down
Print
Author Topic: Adjusting Incidence on a Tumblng Pigeon DT CLG  (Read 716 times)
0 Members and 1 Guest are viewing this topic.
Rewinged
Gold Member
*****

Kudos: 19
Offline Offline

United States United States

Posts: 652



Ignore
« Reply #25 on: August 29, 2018, 08:18:18 PM »

A little late, but in case more pictures help...  This is of a well-trimmed glider, and you can see that there is plenty of room left for adjustment. Since I don't like constructing DT systems, I build the wing and tails but buy the largely completed fuselage from Stan Buddenbohm.
Attached files Thumbnail(s):
Re: Adjusting Incidence on a Tumblng Pigeon DT CLG
Re: Adjusting Incidence on a Tumblng Pigeon DT CLG
Re: Adjusting Incidence on a Tumblng Pigeon DT CLG
Logged

Good air don't care!
Sailaway
Silver Member
****

Kudos: 3
Online Online

United States United States

Posts: 152

Topic starter


Ignore
« Reply #26 on: August 30, 2018, 10:35:17 AM »

Those pictures makes the concept real clear to me. Thanks for taking the trouble. I did order the glider from Stan to learn. I figure a 0.5 or degree  down TE should be about a  32nd on a 3.5 inch chord. So there is enough place to make the whole TE go down as needed. In the photo it appears your left side of the tail is way higher. Is that for the turn or avoid the thumb strike? Or a dihedral on tail? 

Again thanks to all of you. Dan, yes  I just joined the NFFS.
Logged
danberry
Gold Member
*****

Kudos: 17
Offline Offline

United States United States

Posts: 942



Ignore
« Reply #27 on: August 30, 2018, 10:44:23 AM »

Good deal on joining NFFS.

Stab tilt induces glide turn. It will turn toward the high side of the stab.
The story on how this got figured out is a good one.
Logged
flydean1
Gold Member
*****

Kudos: 8
Offline Offline

United States United States

Posts: 639



Ignore
« Reply #28 on: August 30, 2018, 12:11:32 PM »

The story on how this got figured out is a good one.

Well Dan, let us in on it. Huh Huh
Logged
mike
Silver Member
****

Kudos: 5
Offline Offline

United Kingdom United Kingdom

Posts: 118




Ignore
« Reply #29 on: August 30, 2018, 12:17:50 PM »

....Stab tilt induces glide turn. It will turn toward the high side of the stab. ....

Birds showed us this one.  Tilting your tail gives a sideways force to cause yaw.
Attached files Thumbnail(s):
Re: Adjusting Incidence on a Tumblng Pigeon DT CLG
Logged
Rewinged
Gold Member
*****

Kudos: 19
Offline Offline

United States United States

Posts: 652



Ignore
« Reply #30 on: August 30, 2018, 01:14:25 PM »

Glad the pictures were useful!

Yes, the stab tilt is to help the glide turn.  A contest CLG is typically adjusted with a tiny bit of rudder for the climb, and stab tilt for the glide turn.  (L rudder for a flyer who holds the launch stick in their left hand and the glider in their right.  Just bend the rudder near the fuselage a tiny bit, not higher up on the fin.)

With a rearward CG, (and associated minimum decalage as is present in most free flight planes), the stabilizer will be lifting. With a tilted stabilizer, part of that lift force will be sideways, inducing a turn.

The dihedral in my stab is to help avoid the stab strikng my thunb or finger that were holding the glider.  I was told it wouldn't help, but It does seem to help me.
Logged

Good air don't care!
Sailaway
Silver Member
****

Kudos: 3
Online Online

United States United States

Posts: 152

Topic starter


Ignore
« Reply #31 on: August 30, 2018, 08:42:19 PM »

i hurriedly put together a sort of pigeon DT glider to understand the concept. I get it now. Drove to the field to get get a few pulls. On my fourth pull, got a stab strike on me left hand. That was the end time to go home.
So what is your secret to estimate the dihedral on the tail? Can any flat stab be converted to Dihedral. Would i be wrong in saying left side dihedral more than the other to make it turn left after transition ? I think, I will need it too, unless there's a way to adjust( longer?) hold button and the  front hook design?

Just thinking out load, that would it not be great to have V-tail design in such case? Get rid of the rudder ( lighten the tail) and reduce the possibility of stab strike tremendously. However, never seen a CLG with a V-tail design yet.  Just thinking.
Logged
Pages: 1 [2]   Go Up
Print
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Valid XHTML 1.0! Valid CSS!