You MUST be a MEMBER in Hip Pocket Aeronautics "Builders' Forum" to REGISTER for access to the Plan Gallery.
Forum Members can visit This Topic in the Forum to Register. Logging In to the Forum is required.
Home / Radio Control / Radio Control (Foam-Depron) / Sport (Foam-Depron) / Sorta' Jumbo 3D Top Plans  New Items (Last 10 days)  Search  

Registered users

Username:

Password:

Log me on automatically next visit?

» Forgot password

 
Random Plan

Mongoose II 40 (Plan and Article)
Mongoose II 40 (Plan and Article) (hlsat)
Aerobatic, Pattern, Sport
Comments: 0
Downloads: 343

 

Sorta' Jumbo 3D
Sorta' Jumbo 3D

             << ZIP may not work for everyone

Sorta' Jumbo 3D
Description: Now, for something silly, here's the latest in my Sorta Series of 3D planes. What would you never see doing aerobatics? A Boeing 747 Jumbo Jet! So, for your amusement, here is the Sorta Jumbo 3D.
The plans have been uploaded to the Files section of this Group. From your computer (not phone) click on the "Files" or "More" link under the banner picture. Files takes you to the plans. Click on "Sorta Jumbo 3D Plans.pdf" to download. Then print them using the Poster feature in Adobe Reader DC and it will print the plans on letter size paper that you join together with tape.

The planes in this series can be constructed from 2 sheets of Dollar Tree Foam Board (DTFB) at a foam cost of $1.00 per sheet. You'll need four 9g servos, a 270-size motor, 10-20 amp ESC, 4-channel receiver, small piece of 1/8" plywood, and wire for landing gear, & pushrods,

Sorta' Series Model Planes
Recommended Sequence of Assembly

After cutting out all foam parts (and hinging them with 3M NexCare paper tape) and the plywood motor mount, assemble the plane in the following sequence.
I used Clear Gorilla Glue for strength, but hot-melt glue, or other suitable adhesives are acceptable.
1. Drill holes in motor mount to fit.
2. Glue motor mount in vertical part of fuselage and let dry /cure.
3. Cut temporary elevator slot extension. Save the piece to reuse or leave attached by cutting just the horizontal
edges and pushing the slot extension out of the way.
4. Glue elevator in place, replace foam removed in step 3.
5. Cut holes for servos in wing, then glue wing in place. Make sure the wing and elevator are "square" to the fuselage.
6. Glue fuselage sides in place with glue on top of wing, bottom of elevator, and edges of fuselage sides. Cover topside fuselage joint with paper tape to keep Gorilla glue foaming under control. Square everything up and clamp with clothes pins.
7. Form landing gear (if using), punch hole in fuselage and feed landing gear through. You may want to do this step before inserting the wing, but the wire gets in the way while doing step 6. Your call here. Glue the wire to the bottom of the wing and cover with paper tape.
8. Cut hole in fuselage under elevator to fit rudder and elevator servos.
9. Install control horns.
10. If you're going to paint, do it now.
11. Install servos, make pushrods and install them.
12. Cut cockpit sides from .015" acetate to fit and install using narrow strips cut from 3M Clear Mounting Tape.
13. Mount the motor and prop. Position the ESC as needed and secure in place.
14. Position the 4-channel receiver so that the antenna does not come close to the carbon fiber spar and secure in place. The battery will be used for final balancing. Shift it around so that balance is achieved, and fasten it in place using Velcro tape.
15. Enjoy :) :) :) !!!
Keywords: R/C, Electric, 3D, 4-channel, foamie
Date: 04.28.2016 18:27
Hits: 762
Downloads: 284
Rating: 0.00 (0 Vote(s))
File size: 673.4 KB
Added by: DMorrisPE

Comment:
There are no comments for this image



Previous Plan:
Sorta' Juggy 3D (updated 4-18-2016)  		  Next Plan:
Sorta' Spit 3D (updated 4-18-2016)

 

 

RSS Feed: Sorta' Jumbo 3D (Comments)